Castle 110 Pocket Cutter Professional Bundle
The Professional Bundle includes the Base Model along with the following:
- 1 extra Smooth Router Bit (Part B02516)
- 1 8mm Rougher Bit for the Castle 110 (Part B02517)
- 1 extra T20 Torx driver bit, 6" round shaft (Part B00620)
- 1 extra box of 250 count, 1-1/2" Torx Hi-Low pocket screw (Part B04112-0250)
- 1 extra box of 250 count, 1-1/4" Torx Hi-Low pocket screw (Part B04114-0250)
- Castle Face Clamp (Part B40005)
- Castle Tight Access Driver (Part K10020)
Create Castle low-angle, professional pockets in seconds with the Castle 110 Pocket Cutter. The 110 cuts our exclusive low-angle pocket, makes fast, strong, and attractive joints for cabinets, bookcases, face frames and other woodworking projects, and minimizes the joint misalignment common with a drilled pocket. Since the screw's pilot hole is drilled from the opposite side, there is no accumulation of waste or tear out, allowing joined pieces to fit as tightly as possible.
Castle Pockets have smooth clean finishes and join seams flush, minimizing shift.
|Easy to adjust clamp height||Dust Extraction Port (hose not included)||Easy to align and cut perfect pockets every time|
Base Model Includes:
The Professional Bundle includes the Base Model along with the following:
How is the Castle 110 different from the basic pocket jigs that use a drill bit?
There are several major differences. The biggest one is the Castle 110 cuts a 3-degree pocket while the pocket joinery drill guides (using a “2-step” drill bit) drill 15-degree pockets. Why does this matter? Since the screw enters at such a low angle (3 degrees) there is a lot less chance of the two work pieces shifting while assembling them. Another major difference is the Castle 110 cuts the pocket with a router (uses a solid carbide downcut spiral router bit). This means the pockets are crisp and clean even in composite materials like plywood. This is important because you can cut clean pockets on composite materials like plywood and it doesn't destroy the outer veneers like the 2-step drill method. Also, since the Castle pocket are so clean, our pocket plugs blend in much better. Please see the photo below showing cutaway joints of the 15-degree pocket hole next to the Castle 3-degree pocket. The image shows the shifting/misalignment that can occur, and also highlights just how close the screw tip is to the edge on the 15-degree pocket. A typical failure/fracture can occur right at the tip of the screw where it is closest to the edge, leaving a visible fracture on the surface of the work and creating a weaker joint. The Castle joint is typically much stronger due to the screw being closer to the center of the work piece.Check out our Overview video on on the Castle 110.
What thickness of material can I use with the 110?
The Castle 110 was designed for material thicknesses from ½” to 1”, but can handle materials down to 7/16” and up to 1 ½” thick. When cutting pockets materials thicker than 1”, we recommend pocketing both sides of the material for stronger joints.
Are clamps still needed while assembling the joints?
We encourage woodworkers to try the “no-clamp” method with the 110. If you have been using clamps with your current pocket joinery you might be more comfortable continuing the use of clamps. Since the Castle 110 produces a low angle pocket, the chance of any shifting overpowering clamps is practically zero. This is a known problem the 15-degree drill guides. In general, the low angle really minimizes a lot of problems that frustrates woodworkers with pocket joinery.
Any tips on using the “no clamp” method?
Softer woods are typically a little easier than hardwoods when using the "no clamp" method. And of course, straight-grained woods without knots make this process even easier. In woods like oak, the combination of hard and soft grains can contribute to a misaligned screw start by the screw tip diverting to the soft grain. To combat this, you can either run the screw spin backwards briefly or use low pressure at the start. In both cases, it will dig a starting hole more centered with the pilot hole. While the "no clamp" method does take a bit of practice, we recommend clamps if the user is more comfortable with them or if it is a critical joint that absolutely must not shift. In all cases, the Castle 3-degree pocket greatly reduces angular screw pressure to make accurate assembly easier and faster.
How do I change the router bit?
What screws are recommended?
Pan head pocket screws are required. We recommend torx head screws because there is little to no cam-out with the driver while driving the screw. We currently sell pan head pocket screws in 1 1/4” and 1 1/2” lengths. Washer head screws are not compatible with the Castle 110 Pocket system.
What screw lengths do I use?
In general, use 1 ¼” screws on ½” stock and 1 1/2” screws on ¾” and up material. Since the web is adjustable on the Castle 110, you can finetune the length of screw you have to the thickness of the material you are using. We recommend cutting a test pocket to test if enough thread “stick-out” to bite onto the opposing part.
What is the web?
The web is the distance from the end of the material to the start of the pocket. The web is important because you can adjust the web so that you have the appropriate amount of screw thread “stick-out” that will enter the opposing part. The 5 adjustable web settings is a very unique feature of the Castle 110.
Does the Castle 110 need to be adjusted to use different thicknesses of materials?
In general, you can just adjust the web with regards to your screw length and material thickness. The machine ships with Castle factory settings for thicknesses from 5/8” and up. If pocketing 7/16” to 5/8” material, simply place the included overlay plate on the work deck and proceed as normal. The router bit height does not need to be changed.
Does it take longer to cut a pocket with the Castle 110?
The short answer is no. With proper technique and practice you can cut pockets in the same amount time or even shorter than it takes to drill pockets with a 15-degree pocket hole jig.
Does the Castle 110 only cut a partial pilot hole for the screw?
No. Unlike 15-degree pocket hole methods, Castle pilot holes are a "through" hole. The 15-degree drilling method leaves a dimple or trash right at the end of the pilot hole. This dimple/trash material can fall out during assembly and remain between the 2 surfaces causing the joint to not fully close. Glue can complicate the matter since it will hold the trash when applied to the joint. Since the Castle pilot hole is drilled all the way through (our direction of the drilling also helps), dimpling/trash is not a problem.
How do I support long parts or larger panels?
Material supports can be quickly made by taking scrap wood and screwing them together at 90 degrees. A scrap of 2x4 and a piece of plywood at the same height of the work table work great. Simply screw the two pieces together and clamp the support to your bench. The Castle 110 is also mobile. While most of the time the user may want the unit clamped to a bench, you can bring the Castle 110 to the work. Let’s say you have a large case side sitting on saw horses and it need screw pockets around the perimeter. You can simply move and clamp the 110 around the perimeter to cuts pockets. Also, you’re drilling away from you and not towards you in that scenario which can be a benefit in a lot of cases.
I have never heard of Castle before, who is Castle?
Castle has been making screw pocket machines for about 35 years. In the commercial world, the Castle pocket is somewhat the "Kleenex" for pocket cutters. Our smallest machine (beside the 100 and the 110) is a bench top model called the TSM-12. Most of our pocket cutters are floor units about the size of a table saw. We even have a model called the CSI that not only cuts the pocket, but pre-inserts a screw in about 1.5 seconds. The 110 is nice because it’s not only small and affordable, it cuts the same great Castle pocket.
Do you offer plugs to cover the pocket holes?
Yes. We offer plugs in white oak, red oak, maple, cherry, ash, and walnut. Click here to see the available plugs
Do I need to glue the joints I assemble with screw pockets?
Most Castle screw pockets are strong enough that glue is not necessary. One area we recommend glue is when 2 mating surfaces are visual and finish will be applied. Glue will bond the joint so that the 2 surfaces can’t expand/contract over time at different rates. Otherwise, you will eventually see a slight “lip” as the wood moves. Some woodworkers may choose to glue all joints.
Do you sell a 230v version for Europe?
Currently, we do not offer a 230v European version of the 110. We have several customers, however, utilizing step down transformers with good success.
Videos Hide Videos Show Videos
4 Reviews Hide Reviews Show Reviews
I waited 5 months to receive my machine because of parts shortages but it was worth the wait. Truly the best pocket home machine ever. I am so very pleased with my purchase. Thank you Castle!
This machine works as advertised. I am pleased with its performance. I would purchase it again. In addition, their customer service is personable and professional, another plus in my book.
I'm exceptionally pleased with the American Made quality of this wonderfully compact machine. The cuts are clean and precise and the slippage of the boards due to the lower angle is much less than with my previous system. Sadly, I'm sure others will attempt to copy this format, but none will compare the original. If you're thinking about purchasing this or any of Castle's products, don't hesitate. Henry Royce (of Rolls Royce) once stated, "Quality remains after the price is forgotten." I'm looking forward to enjoying this little machine for many, many years to come.
I am just a "hobby" woodworker, if I was full time I would buy one of their larger machines. I have drilled lots of Kreg pockets over the years and these are much cleaner and I suspect because of the pocket angle stronger as well. The machine is well built. I think they have had a bit of assembly issues (spring 2021 & unavailable till fall) . Their service/warranty is excellent as the problems I experienced were resolved. The screws seem to work well, I have not had an oak face frame split yet. The professional bundle has all the components you need.