E10850 - Reed Switch & Magnet, Safety, Router Stop & Drill Stop

Used on TSM-21 for Safety buttons, Router Stop and Drill Stop. Used on TSM-35 for Safety buttons. Used on Line Boring machines as Bit cover safety switch Reed Switch and Magnet, set.

H12075 - Flat Belt (Grey) 1 x 20.75 DG1

Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the H12075 Flat Belt (Blue) 1 x 20.75 DG1 is a spare part you need to have. Engineered to hold up to heavy duty use of an industrial environment. Keep one on hand for a...

N70118-005 5 pack- Button Poly Foot Pad 1 x 1/8"

The clamp foot pad keeps material secured while the pocket is cut and drilled.   This is a 5 pack.

C00200 - TSM Hold Down Foot w/ Pad

P21224 - 3 Port Humphrey Solenoid for TSM-22 (See notes for TSM-21, and TSM-31/TSM-35.)

Humphrey 310, 3 Port Solenoid Specifically engineered for use with the Castle TSM-22, TSM-21 (after SN:61076), TSM-30 series(Clamp function ONLY) line of Pocket Hole Machines the P21224 3 Port Humphrey Solenoid is a spare part you need to have...

P00117 - Router Feed Rate Valve (See notes for TSM-35)

Used on TSM-20, TSM-21, TSM-22, TSM-31, and the TSM-35 as the Router Feed Rate valve. Also used on the TSM-31 and the TSM-35 as the Drill Feed rate and Drill Delay valve. One in each position. SMC Flow Control AS2000-N01

P00018 - 1/8” NPT Brass Muffler/Breather (P00018)

This ⅛ NPT Brass Muffler/Breather will fit the exhaust port in all TSM-21, TSM-22, TSM-35 and TSM-31 3 way and 4 way solenoids. Technical specifications: Thread: 1/8” NPT Material: brass

E00491 - Foot Pedal w/ 8' Cord - Line Master 491-SC36

C00012 - Castle Door Hinge Set w/ Screws (2 Male & 2 Female)

 

P49410 - Parker / Humphrey 410 24V DC Solenoid, 4 port for TSM-35

E03000 - TSM-31/TSM-35 Stop Switch

C30352 - TSM-35 Stop Switch Actuator Assembly Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the C30352 - TSM-35 Stop Switch Actuator Assembly is a spare part you need to have. Engineered to hold up to heavy duty use...

E35010 - TSM-35 "End of Cycle" Switch

Used on TSM-35 for end of cycle sensing on the Drill and Router drive cylinders. Replaces Sick RZT6-03ZUS-KWO end of cycle switch.   Mounting strap may be reused.  If strap needs replacement order pn: E35009 Specifically engineered for...

C00015 - Castle Door Handle Assembly

P01957 - Sioux Air Drill

Sioux air drill for the Castle TSM-35 and TSM-31 Specifically engineered for use with the Castle TSM-35 and TSM-31 pocket hole machines, the P01957 - Sioux Air Drill is an essential component to have on hand. Engineered to hold up to heavy duty use of...

H35013 - TSM-35 Nylon Wear Strip

Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the H35013 TSM-35 Nylon Wear Strip is a spare part you need to have. Engineered to hold up to heavy duty use of an industrial environment. Keep one on hand for a quick...

H00141 - Bar Knob 1/4"-20

H00141 Bar Knob 1/4"-20 Specifically engineered for use with the Castle TSM-21 line of Pocket Hole Machines the H00141 Bar Knob 1/4"-20 is a spare part you need to have. Engineered to hold up to heavy duty use of an industrial environment. Keep one on...

P00538 - Push-In Straight Fitting 1/8"M x 5/32"

Pnuematic push in fittings for TSM 35 and CSI-Next 

N70118 - Button Poly Foot Pad 1 x 1/8"

The clamp foot pad keeps material secured while the pocket is cut and drilled.

G00234 - Bit Gauge Aluminum Bar 1/8" x 1 x 2-3/4"

G00234 - Bit Gauge Aluminum FBar 1/8" x 1 x 2-3/4" Specifically engineered for use with the Castle TSM-21 line of Pocket Hole Machines the G00234 Bit Gauge Aluminum FBar 1/8" x 1 x 2-3/4" is a spare part you need to have. Engineered to hold up to heavy...

P10320 - SQE 10-32 Clippard

Air Management for the TSM-21, TSM-35, TSM-30 and TSM-31. When you are in need of premier woodworking tools and supplies, turn to Castle, Inc. We pride ourselves on providing our customers with the absolute best and highest quality carpentry supplies...

P35300 - TSM-35 Router Cylinder

E35424 - TSM-35 Solid State Control Board

Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the E35424 TSM-35 Solid State Control Board is a spare part you need to have. Engineered to hold up to heavy duty use of an industrial environment. Keep one on hand for a...

E91024 - Sprecher & Schuh Contactor

Sprecher & Schuh CA8-09-10-24Z Contactor for Castle TSM-35 & TSM-31.  Use with TSM-31 Single Phase Sprecher & Schuh Overload (E94061) or TSM-35 230V 3ph Sprecher & Schuh Overload (E94060) or TSM-35 480V 3ph Sprecher &...

P35018 - 1/8 OD 1/16 ID Urethane tubing, Yellow

Tubing to use in the Castle TSM-35 and TSM-31. This product is sold by the foot.For parts and accessories for the TSM-35 the TSM-31 and all of our pocket cutter machines, please check out our service parts selection. For more information about the Castle...

P35125 - TSM-35 Drill Cylinder

P35250 - Humphrey 250A-3-10 Pilot Valve

E35009 - TSM-35 "End of Cycle" Switch Mounting Strap

Used on TSM-35 to mount "End of Cycle" Sick switch pn:E35010 to Drill and Router drive cylinders. Sick BEF-KHZ-RT1-63 Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the E35009 - TSM-35 "End of Cycle"  Switch...

H78065 - TSM-31/35 Router Spindle Bearing

Spindle bearing for TSM-31 and TSM-35 router spindles. -2 are required for the older style router spindle for TSM-31 and TSM-35 machines that have the Porter Cable Chuck and Collet (serial numbers 68269 and below).   -Only 1 H78065 is...

D50044 - Sioux 1/4" Collet

E07041 - Foot Pedals Microswitch

Replaces stock microswitch in all footpedals.

E21016 - 16 Pin Terminal Strip for EL-21 & EL-35 Control Board

Terminal strip for Castle electrical boards. For parts and accessories for the TSM-35, the TSM-31 and all of our pocket cutter machines, please check out our service parts selection. For more information about the Castle line of industrial and personal...

H11775 - Nylon Flat Belt (Green) 1 x 17.75

For use in older TSM-35 machines.  (Unmodified machines with serial numbers 3000 to 54334)   Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the H11775 Nylon Flat Belt (Green) 1 x 17.75 is a spare part you...

E94060 - TSM-35 Low Overload(208V/230V 3 phase) - Sprecher & Schuh

Castle TSM-35 Sprecher & Schuh overload for 3ph 208v /230v. For parts and accessories for the TSM-35, the TSM-31 and all of our pocket cutter machines, please check out our service parts selection. For more information about the Castle line of...

D00710 - Tapered Black Plastic Door Hinge, Male Half

This door hinge is tapered at one end.

E03041 - TSM-35 Start Switch

C30351 - TSM-35 Start Switch Actuator Assembly Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the C30351 - TSM-35 Start Switch Actuator Assembly is a spare part you need to have. Engineered to hold up to heavy duty...

P35026 - Parker 02FA06A 1/4" Disposable In-Line Filter

When running an air system on your Castle TSM-35 pocket hole machine, it is critical to install quality components for air management. A 1/4" Disposable In-Line Filter ensures that the air system runs safely, it protects the machine as well as the...

C00215 - Complete TSM Clamp Cylinder Assembly

Used on TSM-20, TSM-21, TSM-22, TSM-31, and TSM-35. Clamp cylinder assembly: complete with Air inlet fitting, Clamp Foot, Foot pad, Jamb Nut and Mounting Nut.

P00215 - TSM Clamp Cylinder

Used on TSM-20, TSM-21, TSM-22, TSM-31, and TSM-35 Note: Clamp Foot sold separately

C35005 - TSM-35 Drill Delay Valve Assembly

C35005 - TSM-35 Drill Delay Valve Assembly Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the C35005 TSM-35 Drill Delay Valve Assembly is a spare part you need to have. Engineered to hold up to heavy duty use of an...

F14219 - 1/4-20 x 2” Ribbed Neck Carriage Bolt

Whether you need a speciality bolt for your Castle 100 or a special pneumatic fitting for your dust collection system, we have what you are looking for. If you do not see what you need, contact us for more information!    

F14458 - 1/4-20 x 1-1/4" Socket Head Cap Screw For Pocket Cutter Machine

This set screw is used to adjust left/right carriage position on the TSM-21 and TSM-35. It is also used as the threaded mounting post for the porter cable 7301 in the TSM-21. When you are in need of premier woodworking tools and supplies, turn to Castle,...

C35002 - Clippard TSM-31/35 Filter/Regulator/Luber Assembly

This Clippard branded FRL will retro fit to all TSM-35 and TSM-31 machines. Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the C35002 TSM-35 Filter/Regulator/Luber Assembly is a spare part you need to have...

N35313 - TSM-31/35 Router Spindle, old PC Style

Older style Router Spindle for TSM-31 and TSM-35 machines that have the Porter Cable Chuck and Collet (serial numbers 68269 and below).  This Router Spindle will NOT work with newer machines that have the new Bosch chuck and collet system...

C35101 - TSM-35 Safety Blade Assembly

C35101 - TSM-35 Safety Blade Assembly Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the C35101 TSM-35 Safety Blade Assembly is a spare part you need to have. Engineered to hold up to heavy duty use of an industrial...

D00720 - Tapered Black Plastic Door Hinge, Female Half

This door hinge is tapered at one end.

D50055 - TSM-31/35 Router Chuck, old PC style

Older style Router Chuck for TSM-31 and TSM-35 machines that have the Porter Cable Chuck and Collet (serial numbers 68269 and below).  This Router Collet will NOT work with newer machines that have the new Bosch chuck and collet system...

E03340 - TSM-31/35 Safety Interlock Switch

Safety Interlock Switch IDEC HS5D-11ZRNM can be used in place of Siemens brand switches. Please confirm interlock brand before purchase. For parts and accessories for the TSM-35, the TSM-31 and all of our pocket cutter machines, please check out our...

N35352 - TSM-31/35 Spindle Housing, old PC style

Older style Spindle housing for TSM-31 and TSM-35 machines that have the Porter Cable Chuck and Collet (serial numbers 68269 and below).  This spindle housing will NOT work with newer machines that have the new Bosch chuck and collet system...

M00235 - Foot Switch Guard - Yellow

P14018 - 1/8 NPT x 1/4 Push In Swivel Elbow

F11412 - 1-1/4-12 Jam Nut, Zinc Plated

Used to hold the clamp cylinder in place.

N35353 - TSM-35 Small Pulley

Specifically engineered for use with the Castle line of Pocket Hole Machines the N35353 TSM-35 Small Pulley is a spare part you need to have. Engineered to hold up to heavy duty use of an industrial environment. Keep one on hand for a quick change in...

E35420 - Air Pressure Switch - OBSOLETE

NOTE: The air pressure switch is no longer used in the TSM-31 and the TSM-35. Its removal does not constitute a safety issue.  Customers with older machines with pressures switches can bypass them by following the instructions in the TSM-31/TSM-35...

E16224 - 24 VDC Fuse

Fuse for Castle TSM-35 transformer E55750/E35713. Keep one or two of these fuses handy for those times when the fuse blows. Make sure that you are not stranded in the middle of your project due to a blown fuse. Castle carries a variety of spare parts,...

E91827 - TSM-35 High Overload(480v 3 phase) - Sprecher & Schuh

TSM-35 High Voltage (480V 3 phase) Overload to be used with Sprecher & Schuh contactor CA8-09-10-24Z. Please note: not compatible with contactor CA4-9-10-24

O15858 - TSM-31/35 Router Cylinder Bumper

O15858 - TSM-31/35 Router Cylinder Bumper Rubber bumper for the router cylinder for the Castle TSM-35 and TSM-31.  If you need to order a new router cylinder, this bumper is included with part C35021 - TSM-35 Router Drive Cylinder Assembly

C35022 - TSM-35 Drill Cylinder Assembly

Complete drill cylinder assembly for the Castle TSM-35 and TSM-31. Comes complete, ready to install.

M35017 - TSM-35 Drill Motor Plate

Sioux Drill Motor Mounting Plate.

P35081 - Clippard TSM-31/35 Lubricator

Clippard Lubricator for Castle TSM-35 and TSM-31.  Use with Clippard Filter/Regulator Castle part P35080. For parts and accessories for the TSM-35 the TSM-31 and all of our pocket cutter machines, please check out our service parts selection. For...

C00010 - Castle Front Door Assembly

Includes the following:   D00710 Black plastic door hinge, male half (D1405) x2  F10010 #12X1/2 Self Tapping SMS (F1058) x4  G00101 Door Spring Clip Assembly x1  H00141 1/4-20 Bar Knob (H700)  x1  F14125 1/4-20 x 1/2...

C35021 - TSM-35 Router Drive Cylinder Assembly

Drop in replacement for the TSM-35 or TSM-31 router cylinder. Comes complete with clevis, air fittings and bumper. For parts and accessories for the TSM-35 the TSM-31 and all of our pocket cutter machines, please check out our service parts selection...

E03322 - Security Switch Key, ABB LSA30

E03322 - Security Switch Key, ABB LSA30 Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the E03322 Security Switch Key, ABB LSA30 is a spare part you need to have. Engineered to hold up to heavy duty use of an...

TSM-31/35 Router Spindle Assembly, New Bosch style

New Bosch Style TSM-31/TSM-35 Router Spindle Assembly.  This is our latest spindle with a Bosch chuck and collet.     Note: The old Porter Cable style spindle assembly is NO longer available. Machines with serial numbers...

E03300 - ABB LS35 Security Interlock Switch

  Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the E03300 ABB LS35 Security Interlock Switch is a spare part you need to have. Engineered to hold up to heavy duty use of an industrial environment. Keep one on...

P01814 - Legris 1/8” NPT Female x 1/4” Straight Push-To-Connect Fitting (P01814)

Legris 1/8” NPT Female x 1/4” Straight Push-To-Connect Fitting is used on the TSM-35 to connect the air pressure switch to the airline. Push-in fittings allow fast circuit assembly for conveying compressed air, gas or liquids at a wide range...

P35066 - Parker TSM-31/35 Filter/Regulator

When running an air system on your Castle TSM-35 pocket hole machine, it is critical to install quality components for air management. A Parker lubrication and filter system ensures that the air system runs safely, it protects the machine as well as the...

H00058 - Bushing QT 5/8"

Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the H00058 - Bushing QT 5/8" is a spare part you need to have. Engineered to hold up to heavy duty use of an industrial environment. Keep one on hand for a quick change...

1/4-20 x 1-1/2 U-Bolt TSM-31/35 (F523)

1/4-20 x 1-1/2 U-Bolt for mounting TSM-31/35 router spindle, QTY 2 required (F523).

P35067 - Parker TSM-31/35 Lubricator

When running an air system on your Castle TSM-35 pocket hole machine, it is critical to install quality components for air management. A Parker lubrication system ensures that the air system runs safely, it protects the machine as well as the components...

C35001 - TSM-35 Rapid Index Assembly

Rapid Index Assembly for models TSM-31 and TSM-35 only.  Will not work with any other Castle machine model.

P35389 - TSM-35 3/8" Drill Hose Assembly

When running an air system on your Castle TSM-35 pocket hole machine, it is critical to install quality components for air management. The ⅜” drill hose ensures that the air system runs safely. Ideal for vacuum systems, blowers, and more!...

D10140 - Sioux Collet Nut 1/4"

E35715 TSM-31/TSM-35, transformer, .50 KVA

 

M35011 - TSM-35 Flywheel

TSM-35 Flywheel.  This part is located on the Router Spindle Assembly. Made to hold up to the the heavy duty use that the TSM-35 Pocket Hole Machine is designed for. Keep one on hand for quick change in order to keep production steady. Please...

1/4 NPT Red Plastic Plug (P2900)

1/4 NPT Red Plastic Plug (P2900)

1/8 NPT x 10-32 Bushing, Brass (P317)

1/8 NPT x 10-32 Bushing, Brass (P317)

Bosch 1617 Collet Wrench Set (Black)

Bosch 1617/1617EVS Collet Wrench Set

D50012 - 1/2" Collet Assy for Porter Cable #6902

1/2" collet assembly for the Porter Cable 6902 router.  Note: If using our standard 3/8" diameter router bits, you will need Part, N00538 - 1/2" to 3/8" Collet Reducer  

E35001 - Telemecanique Interlock Switch

TSM-35 interlock switch - used on older machines.  Please confirm interlock brand before purchase.

C35115 - TSM-35 Motor Pulley Assembly

Pulley assembly for the Baldor or Leeson motor on the TSM-30 series machine.

D35001 - Bosch 1/2" Collet Assembly

D35001 - Bosch 1/2" Collet Assembly for Bosch 1617 and 1617EVS routers.   Note: you will need a collet reducer for our 3/8" shank router bits, part number N00538 - 1/2" to 3/8" Collet Reducer

TSM-31/35 Safety Interlock Key (E260) IDEC

TSM-35/TSM-31 Safety Interlock Key (E260) IDEC HS9Z-A52A for IDEC Interlock Switches IDEC HS5D-11ZRNM

H35005 - TSM-35 Motor Slinger for Baldor/Marathon motors

H35005 - TSM-35 Motor Slinger for Baldor/Marathon 3 phase motors Specifically engineered for use with the Castle TSM-35 line of Pocket Hole Machines the H35005 TSM-35 Motor Slinger is a spare part you need to have. Engineered to hold up to heavy duty...

P35070 - TSM-35 Gauge

When running an air system on your Castle TSM-35 pocket hole machine, it is critical to install quality components for air management. A gauge ensures that the air system runs safely, it protects the machine as well as the components attached to the air...

T30466 - # 30466 11/16 Wrench for a Sioux 1954HPHT

# 30466 11/16 Wrench for a Sioux 1954HPHT

1/4 NPT x 3/8 PI Elbow - Legris (P233)

1/4 NPT x 3/8 PI Elbow - Legris (P233)

10-32 X 5/8 Button Head Cap Screw S.S. (F833)

10-32 X 5/8 Button Head Cap Screw S.S. (F833)

3/8 x .062 Black Polyethylene Tubing per foot

3/8 x .062 Black Polyethylene Tubing, sold by the foot

E35501 Baldor VEM3550 1-1/2HP 3 Phase Motor for TSM-35

E35501 Baldor VEM3550 1-1/2HP 3 phase motor for TSM-35 for Serial #63657 and below.  Use motor slinger H00604.

E35502 - TSM-35 Marathon 1HP Motor 3 phase

E35502 - TSM-35 Marathon 1HP 3 phase motor.   Direct replacement for a TSM-35 that came with Baldor or Leeson motors.  Use motor slinger H35005.   Note: not for TSM-31 models

H00250 TSM-31 Motor Slinger for Baldor motors (H802)

H00250 TSM-31 Motor Slinger for Baldor single phase Motors (H802)

H00604 TSM 31/35 Motor Slinger Leeson/older Baldor Motors(H800)

H00604 Motor slinger for TSM-35 Leeson 3 phase motors and for older TSM 31 Baldor Motors (H800) 006043.05

Humphrey Rod Clevis (D418)

original part number d07130

P35068 - Parker TSM-31/35 FRL Mount Bracket PS955P

P35069 - Parker TSM-31/35 FRL Connector

P35080 - Clippard TSM-31/35 Filter/Regulator w/ Gauge

Clippard brand Filter/Regulator with gauge for use the the TSM-35 and TSM-31. Use with Clippard lubricator, Castle part P35081. For parts and accessories for the TSM-35 the TSM-31 and all of our pocket cutter machines, please check out our service parts...

P50638 - In-Line Check Valve 3/8"

When running an air system on your Castle pocket hole machine, it is critical to install safeguards that contribute to responsible air management. The one way, inline check valve prevents pressure spikes in the system and protects the pump. Ideal for...

Scratch and Dent, Castle Front Door Assembly for TSM Series

Front Door Assembly, Complete with Hinges & Door Knob Includes the following: D00710 Black plastic door hinge, male half (D1405) x2  F10010 #12X1/2 Self Tapping SMS (F1058) x4  G00101 Door Spring Clip Assembly x1 H00141 1/4-20 Bar...

T30465 - # 30465 9/16 Wrench for Sioux 1954HPHT

# 30465 9/16 Wrench for Sioux 1954HPHT

TSM-31/35 Router Spindle Top Bearing - New Bosch Style

Top spindle bearing for TSM-31 and TSM-35 router spindles with the new Bosch chuck and collet system (serial numbers 68270 and up).  -Only 1 H78088 router spindle bearing is required for the top of the spindle.   For the...